HOKUYO UBG-05LN Laser Range Finder
The UBG-05LN is a programmable laser distance measuring and obstacle detection scanner.
Compact laser obstacle detection sensor with wide detection range (5m x 4m)
-
Automated Guided Vehicles
-
Robotics
-
Security
-
Automation
Features
- Operating principle is that semicircular field is scanned by laser(λ=785nm) and the coordinates is calculated by measuring distance to object and its step angle and it detects obstacles in setting area.
- Scanning angle(detecting area) is 180° and detecting area can be free to set with 0.1 to 5m(length) and 4m(width) and it can set detecting distance with 3 steps output per each area.
- It can change the detecting area(31 kinds max.) that was set beforehand by outer bit input.
- Power source is 24VDC and current consumption is 150mA or less.
Model Number | UBG-05LN |
Power Source | 24VDC (available operating range 18 to 30VDC, ripple within 10%) |
Current Consumption | 150mA or less but rush current 300mA is required when start-up (when 24VDC) |
Light Source | Semiconductor laser diode (λ=785nm), Laser safety class 1 (FDA) |
Detectable Object |
White paper with 1252 (Installing in parallel with projecting/receiving surface) |
Detecting range | Area with 0.1 to 5m (length) and 4m (width) (origin point is the scanning center) |
Accuracy*1 | ±20mm at 1m or less, 2% of measurement at 1m or more |
Repeatability*1 | ±10mm at 1m or less, 2% of measurement at 1m or more |
Detecting are setting | Output 1 : It is free to set from 0 to 5m for optical axis direction with 7 points pointer. Output 2, 3 : (1) Linear setting to progressive direction (2) Fan-shaped setting to optical axis direction (3) Percentage (%) setting against output 1 pointer |
Hysteresis | 6.25% of detecting distance |
Output |
Photo-coupler/open-collector output (30VDC 50mA or less) Output 1 : OFF when detected in area Output 2 : OFF when detected in area Output 3 : OFF when detected in area Output 4 (Trouble output) : ON during normal operationNote1) |
Output response time | 210msec or less(scanning speed 100msec/rev.)Note2) |
Input | Photo-coupler input(Anode common, Each input ON current 4mA) Detecting area changeover Set area No. by [Input 1], [Input 2], [Input 3], [Input 4] and [Input 5] Emission-stop by getting all [Input 1], [Input 2], [Input 3], [Input 4] and [Input 5] to ON (OFF : H level input, ON : L level input) |
Input Responce Time | Input taking-in cycle : 1 scanning time (100msec) (1msec when choosing emission-stop by outer input |
Starting Time | Within 10sec from putting power source on (It may exceed this time depending on the starting condition) |
Indicators | Power lamp (Green) : Flickers when troubled or started Output 1 lamp (Orange) : Lights up when detected in area Output 2 lamp(Orange) : Lights up when detected in area Output 3 lamp (Orange) : Lights up when detected in area |
Connection | Cable 1m Long |
Ambient illuminanceNote 3) | Halogen/mercury lamp : 10,000lx or less, Fluorescent lamp : 6,000lx (Max.) |
Ambient temperature/ humidity | -10 to +50 degrees C, 85%RH or less(Not condensing, not icing) |
Vibration resistance | 10 to 55Hz, double amplitude 1.5mm Each 2 hour in X, Y and Z directions |
Impact resistance | 196m/s2 Each 10 time in X, Y and Z directions |
Protective structure | IP64 (IEC standard) |
Weight | 185g (260g with cable) |
Life | 5 years (motor life) |
Material | Front case : polycarbonate, rear case : ABS |
*2 Accuracy test is made by standard reflector when shipment
Note 1) Output 1 to 3 show the state that detecting object is existing when trouble output was executed.
Note 2) More 1 scanning is delayed if area changeover was made.
Note 3) It may cause malfunctions when receiving strong light such as sun light etc.
Connections
Colours | Signals |
Black | Output 1 |
White | Output 2 |
White (Blue) | Output 3 |
Orange | Output 4 (Trouble output) |
Gray | Output common minus |
Red | Input common plus |
Green | Input 1 |
Yellow | Input 2 |
Purple | Input 3 |
White (Yellow) | Input 4 |
White (Purple) | Input 5 |
Brown | +VIN?24VDC? |
Blue | -VIN |
Yellow (Red) | Serial input (RXD) |
Yellow (Green) | Serial output (TXD) |
Yellow (Black) | Serial GND |
Note 1) Colours in parenthesis indicate ink color of both sides line printing. Note 2) Connect unused input wires to input common plus(Red) or open it. Connect unused output wires to output common minus(Gray) or open it. Note 3) Input/output direction is mentioned on the basis of UBG-05LN.
Input/Output Circuit
External Dimensions
System Structure
* Scanning angle 180° and step angle 0.36° with 500 steps
Image | Product Name | Description | Price | Action | |
---|---|---|---|---|---|
![]() |
HOKUYO UBG-04LX-F01 Robotics Laser | The HOKUYO UBG-04LX-F01 is a state of environment detection sensor specifically designed for intelligent robotics applications.Scanning speed is 4 times faster than URG-04LX, providing better performance for autonomous robots.View Detail... |
£2,130.00
£1,775.00
As low as
£2,505.60
|
||
![]() |
HOKUYO URG-04LX Robotics Laser | The HOKUYO URG-04LX is a state of the art laser range finder is suitable for next generation intelligent robots with an autonomous system and privacy security.Suitable for autonomous service robots as a means of environment, and self-View Detail... |
£1,890.00
£1,575.00
|
||
![]() |
HOKUYO URG-04LX-UG01 Laser Range Finder | The URG-04LX-UG01 is the smallest and lightest LRF available.With a single USB connection it is ideally suited to students and researchers who are involved in robotics.
View Detail... |
£1,050.00
£875.00
|
||
![]() |
HOKUYO UTM-30LX Robotics Laser | The HOKUYO UTM-30LX is a state of detection sensor specifically designed for intelligent robotics applications.Suitable for robots with higher moving speed because of the longer range and fast response.
|
£4,182.00
£3,485.00
|
||
![]() |
HOKUYO PBS-03JN Infrared Range Finder | The PBS-03JN has a wide scanning area and is a popular alternative to laser range-finders in indoor environments.The sensor is popular due to its low cost, low power consumption and light weight design.
|
£966.00
£805.00
|