(0) items


You have no items in your shopping cart.

Intel Galileo Gen 2

Product Code: 102110003
Excl. VAT: £59.00 Incl. VAT: £70.80
You will earn 59 Robo Points for buying this product

Intel Galileo Gen 2 development board, the first in a family of Arduino-certified development boards based on Intel architecture, and specifically designed for makers, students, educators and DIY electronics enthusiasts.

Based on the Intel Quark SoC X1000, a 32-bit Intel Pentium processor-class system on a chip (SoC), the genuine Intel processor and native I/O capabilities of the Intel Galileo board deliver great performance, and a broad spectrum of hardware peripheral, and software support. The board also provides a simpler and more cost-effective development environment compared to the Intel Atom Processor- and Intel Core processor-based designs.

 What’s new with Intel Galileo Gen 2

•6-pin 3.3V USB TTL UART header replace 3.5mm jack RS-232 console port for Linux debug. New 6-pin connector mates with standard FTDI USB serial cable (TTL-232R-3V3) and popular USB-to-Serial breakout boards.

•12 GPIOs now fully native for greater speed and improved drive strength.

•12-bit pulse-width modulation (PWM) for more precise control of servos and smoother response.

•Console UART1 can be redirected to Arduino headers in sketches, eliminating the need for soft-serial in many cases

•12V Power-over-Ethernet (PoE) capable (PoE module installation required).

•Power regulation system changed to accept power suppliers from 7V to 15V.


•Intel Quark SoC X1000 application processor, a 32-bit, single core, single-thread, Pentium instruction set architecture (ISA)-compatible CPU, operating at speeds up to 400MHz.

•Support for a wide range of industry standard I/O interfaces, including a full-sized mini-PCI Express slot, 100Mb Ethernet port, Micro-SD slot, USB host port, and USB client port.

•256 MByte DDR3, 512 Kbyte embedded SRAM, 8 MByte NOR Flash, and 8 Kbit EEPROM standard on the board, plus support for MicroSD card up to 32GB.

•Hardware-/pin-compatibility with a wide range of Arduino Uno R3 shields.

•Programmable through the Arduino integrated development environment (IDE) that is supported on Microsoft Windows, Max OS, and Linux host operating systems

•Support for Yocto 1.4 Poky Linux release.




Intel Quark SoC X1000

400 MHz


32-bit Intel Pentium processor-compatible ISA

16 KB

512 KB on-die, embedded; 800 MT/s

Technologies Supported
Integrated real-time clock

Optional 3 V coin cell battery for operation between turn-on cycles


8 MB NOR Flash

256 MB DDR3

SD Card (Optional)
Up to 32 GB

Compatible with any USB 2.0 storage device

8 KB


123.8mm (L) x 72.0mm (W)

6-pin console UART

6-pin ICSP


RJ45 Ethernet, Power over Ethernet capable

USB 2.0 Host (standard Type A)

USB 2.0 Client (micro-USB Type B)

Mini-PCI Express 1x slot

Jack with increased range (7 to 15 V)

Supports Power-over-Ethernet (requires PoE module installation)

Header for RTC power

Reset for sketch and attached shield resets 10/100 Mbps Ethernet

Reboot to reset the Intel Quark SoC X1000

Whenever possible, items which are in stock are dispatched the same day, or the next working day.

Large and/or heavy items are dispatched by UPS courier service and these orders must be placed before 15:00hrs (GMT) to ensure same day dispatch.

Small items are normally sent using a Royal Mail service for UK orders, and International Airmail or UPS for overseas orders

Returns Policy

Intel Galileo Gen 2 pack

Enquiry Us

Post your comment

Active Robots