0800 756 9913Sales Order Line Mon-Fri 9am-5pm

LJ-UE9PRO - Ethernet and USB 24-Bit Multifunction DAQ unit

Product Code: UE9-PRO

Availability: In stock

Excl. VAT: £432.95 Incl. VAT: £519.54
You will earn 432 Robo Points for buying this product
OR

All the functions of the standard LabJack UE9 but with the addition of a high resolution 24-bit ADC.

  • 14 x Analogue Inputs
  • 02 x Analogue Outputs
  • 23 x Digital Inputs
  • 23 x Digital Outputs
  • 14 Analogue Inputs
  • Expandable to 80 single ended or 40 differential with the Mux80 Card
  • Dual ADC design - 12/16 bit high speed, 24-bit low speed, high resolution
  • ±5 or 0-5 Volt Maximum Analogue Input Range
  • Up to 50kHz streaming to disk
  • PGA with Gains of 1, 2, 4, or 8 (Unipolar Ranges Only)
  • Supports Software or Hardware Timed Acquisition
  • Can connect to thermocouple directly
  • 2 Analogue Outputs (12-Bit)
  • 23 Digital I/O (Up to 50 Hz per I/O)
  • Up to 2 Counters (32-bits each)
  • Up to 6 Timers (Pulse Timing, PWM Output, Quadrature Input)
  • Built-In Screw Terminals for Some Signals
  • All I/O routed to edge D-type connectors
  • USB 2.0/1.1 (Full Speed) Interface
  • Ethernet 10baseT Interface
  • MODBUS TCP protocol Supported
  • Electrical Isolation Possible with Ethernet Interface
  • No Power Supply Needed for USB Operation - includes PSU for Ethernet use
  • DAQFactory Express Software
  • Supported by ProfiLab and RealView software
  • LabVIEW VI's and software examples
  • Includes USB and Ethernet Cable, Power Supply, and Screwdriver
  • Free Firmware Upgrades
  • Enclosure Size Approximately 75mm x 175mm x 25mm
  • Rated for Industrial Temp Range (-40 to +85 °C)

Analogue Inputs

The LabJack UE9 has 14 external analogue inputs (AIN0-AIN13) and 2 internal analogue inputs (AIN14-AIN15). AIN0-AIN3 are available on screw terminals and also on the DB37 connector. All 14 analogue inputs are available on the DB37 connector. The Mux80 multiplexer can expand this to to 80 single ended or 40 differential channels.

Each analogue input can be configured individually as unipolar (0-5 volts) or bipolar (±5 volts). An internal PGA provides gains of 1, 2, 4, or 8 (unipolar ranges only at this time). Analogue input resolution is 12-bits at max speed (10 us conversion time giving 50kHz rate), increasing up to 16-bits at slower speeds (10 ms conversion time).

The UE9-Pro has an additional resolution setting that causes acquisitions to use the alternate high-resolution converter (24-bit sigma-delta). Resolution is configured on a device basis, not for each channel.

Thermocouples

It is possible to connect thermocouples directly to the UE9, if you don't require great accuracy: a resolution of ±1 °C is achievable. You need set the resolution to maximum (17 bits) and use the highest gain setting. The UE9 has an internal temperature sensor, which can be used for cold junction compensation. DAQFactory contains thermocouple linearisation as a built-in conversion function. A DAQFactory thermocouple example will be available shortly.

Analogue Outputs

The LabJack UE9 has 2 analogue outputs (DAC0 and DAC1) that are available both on screw terminals and the DB37 connector. Each analogue output can be set to a voltage between 0 and about 4.8 volts with 12-bits of resolution.

Digital I/O

The LabJack UE9 has 23 digital I/O channels which can be individually configured as input, output-high, or output-low. 8 of these lines are called flexible digital I/O (FIO) and can be software configured as up to 6 timers and 2 counters.

The first 4 FIO are available on screw terminals and the DB37 connector. All 8 FIO and 3 MIO are available on the DB37 connector, and 8 EIO and 3 CIO are available on the DB15 connector.

Up to 6 FIO can be configured as timers. The timers are very flexible, providing options such as PWM output for motor control, pulse timing, and quadrature input. Up to 2 FIO can be configured as 32-bit counters.

Software

LJLogUD

A Ready-to-run executable logs from 1-16 channels on a U3, U6, or UE9. Displays selected channels on a graph and writes data to file. Executable requires the LabVIEW 6.0 run time engine (which can coexist with other versions of the LVRTE).

LJStreamUD

For faster acquisitions use the ready-to-run executable which streams analog inputs from 1-16 channels on a U3, U6, or UE9. Displays selected channels on a graph and writes data to file. Executable requires the LabVIEW 6.0 run time engine (which can coexist with other versions of the LVRTE).

LabVIEW

Supplied with LabVIEW VI's. These VIs make use of the native TCP capability of LabVIEW. They do not require any special LabJack drivers, and thus should work on any LabVIEW platform that supports TCP

Programming

If you know any language we probably support it. This includes C, C++, C#, Delphi, Java, LabVIEW, LabWindows/CVI, MATLAB, Python, and Visual Basic (VB6/VB.NET). Start on the UD Series Programming page.

DAQFactory Express

The free Express version of DAQFactory works with the U12. DAQFactory allows non-programmers to make custom applications. It is easy to collect input data, convert to engineering units, display it, and log it to file, without any programming. Scripting is also supported so you can do advanced applications with control and automatic setting of outputs.

View FileLabJack U9 User Guide    Size: (2.56 MB)

Additional Information

Video No

You may also be interested in the following product(s)

LJTick-Proto Board

LJTick-Proto Board

More info
EI1034 Temperature Probe

EI1034 Temperature Probe

More info
LJTick-RelayDriver

LJTick-RelayDriver

More info