+44 (0) 1761 234 328

(0) items

£0.00

You have no items in your shopping cart.

Pololu Adjustable Boost Regulator 4-25V

Product Code: 799
Excl. VAT: £10.40 Incl. VAT: £12.48
You will earn 10 Robo Points for buying this product

The Pololu adjustable boost regulator is a very flexible switching regulator (also called a switched-mode power supply, SMPS, or DC-to-DC converter) that can generate voltages higher than its input voltage.



  • Output adjustable from 4 V to 25 V.

The output voltage can be set using the trimmer potentiometer in the upper-right corner of the board. The input voltage range is 1.5 V to 16 V (the input voltage should be kept below the output voltage). The integrated 2 A switch allows for output currents high enough to drive small motors, as in the 3pi robot, and allows large voltage gains, such as obtaining 24 V from two NiMH cells.

Some example applications include:

  • Powering 5 V systems from lower-voltage batteries.
  • Powering 5 V subsystems (e.g. sensors) in lower-voltage (e.g. 3.3 V) systems.
  • Achieving consistent actuator operation when powered by fluctuating batteries
  • Powering high-brightness LEDs or a large number of LEDs in series

Using the Boost Regulator

The boost regulator has just three connections: the input voltage, ground, and the output voltage. These three connections are labeled on the back side of the PCB, and they are arranged with a 0.1" spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1" grid. You can solder wires directly to the board or solder in either the 3×1 straight male header strip or the 3×1 right-angle male header strip that is included.

Feature Summary

  • Input voltage: 1.5 V to 16 V
  • Output adjustable from 4V to 25V
  • 750 kHz switching frequency
  • 2 A switch (and input) limit
  • integrated over-temperature and over-current shutoff
  • typical efficiency of 80-90% when doubling voltage and with 100-500 mA output
  • Small size: 10.7 x 22.4 x 5.8 mm (0.42″ x 0.88″ x 0.23″)
  • Weight without header pins: 1.6 g (0.06 oz)
Warning: You should be careful not to use an input voltage that exceeds the output voltage setting, so we recommend setting the output voltage with the input voltage around or below 2.5 V (e.g. using one or two alkaline batteries). Note that the potentiometer has no physical end stops, which means that the wiper can be turned 360 degrees and into an invalid region in which the output voltage is set to approximately 2.5 V (for both the 2.5 V to 9.5 V and 4 V to 25 V versions).

Gerneral Specification:
  • Minimum operating voltage: 1.5V
  • Maximum operating voltage: 16V (Absolute max. The operating voltage should not exceed the set output voltage, VOUT.)
  • Minimum output voltage: 4V
  • Maximum output voltage: 25V
  • Reverse voltage protection: No
  • Maximum quiescent current: 30mA (With no load. Actual quiescent current ranges from 2 to 30 mA depending on input voltage and output voltages.)

Product Attachments

View FileNCP1402 Datasheet    Size: (202.95 KB)

FeeFo Reviews

Date / Score
Customer Comment Our Response
30-Jul-2015 Product:
I don't want to write comments.
Read more reviews on Feefo
Feefo reviews 100% 1

Whenever possible, items which are in stock are dispatched the same day, or the next working day.

Large and/or heavy items are dispatched by UPS courier service and these orders must be placed before 15:00hrs (GMT) to ensure same day dispatch.

Small items are normally sent using a Royal Mail service for UK orders, and International Airmail or UPS for overseas orders

Returns Policy

Pololu Adjustable Boost Regulator 4-25V with headers
0
Post your comment

Active Robots