Accelerometer Interface Board
ADXL202JE ±2g

Interface board for the ANALOG DEVICES accelerometers in the E8 package. The ADXL is a solid state MEMS accelerometer with digital PWM or Analogue output.

The ADXL can measure both static and dynamic acceleration. This means the ADXL is suited well for sensing tilt (used in many Glove / Air Mouse applications) and for sensing brute acceleration (rocketry and general motion sensing applications).

More Information & Downloads

Accelerometer Interface Board
ADXL203CE ±1.5g

Interface board for the ANALOG DEVICES accelerometers in the E8 package. The ADXL is a solid state MEMS accelerometer with digital PWM or Analogue output.

The ADXL can measure both static and dynamic acceleration. This means the ADXL is suited well for sensing tilt (used in many Glove / Air Mouse applications) and for sensing brute acceleration (rocketry and general motion sensing applications).

More Information & Downloads

Accelerometer Interface Board
ADXL213AE ±1.2g

Interface board for the ANALOG DEVICES accelerometers in the E8 package. The ADXL is a solid state MEMS accelerometer with digital PWM or Analogue output.

The ADXL can measure both static and dynamic acceleration. This means the ADXL is suited well for sensing tilt (used in many Glove / Air Mouse applications) and for sensing brute acceleration (rocketry and general motion sensing applications).

More Information & Downloads

Accelerometer Interface Board
ADXL311 ±2g

Interface board for the ANALOG DEVICES accelerometers in the E8 package.

The ADXL is a solid state MEMS accelerometer with digital PWM or Analogue output. The ADXL can measure both static and dynamic acceleration.

This means the ADXL is suited well for sensing tilt (used in many Glove / Air Mouse applications) and for sensing brute acceleration (rocketry and general motion sensing applications).

More Information & Downloads

Accelerometer Interface Board
ADXL320 ±5g

Interface board for the dual axis ADXL32x accelerometers. Brings out the Analogue voltage levels from the X and Y axis to a standard 0.1" header.

The ADXL320 can be powered from 2.4V-5.25V. The Self-Test pin can be used to verify sensor operation.

Board comes fully assembled and tested with selected sensor and 0.1uF filtering capacitors.

More Information & Downloads

Accelerometer Interface Board
ADXL321 ±18g

Interface board for the dual axis ADXL32x accelerometers. Brings out the Analogue voltage levels from the X and Y axis to a standard 0.1" header.

The ADXL321 can be powered from 2.4V-5.25V. The Self-Test pin can be used to verify sensor operation.

Board comes fully assembled and tested with selected sensor and 0.1uF filtering capacitors.

More Information & Downloads

Accelerometer Interface Board
ADXL322 ±2g

Interface board for the dual axis ADXL32x accelerometers. Brings out the Analogue voltage levels from the X and Y axis to a standard 0.1" header.

The ADXL322 can be powered from 2.4V-5.25V. The Self-Test pin can be used to verify sensor operation.

Board comes fully assembled and tested with selected sensor and 0.1uF filtering capacitors.

More Information & Downloads

Click to Enlarge

Serial Accelerometer
Tri-Axis v5 - Dongle

The SerAccel v5 is a 3 axis accelerometer up to +/-6g with a simple serial interface. The latest SerAccel development, version 5 has many new improvements including variable baud rate, a factory reset command, and a complete triple axis measurement system based on the newly released MMA7260Q sensor from Freescale.

The SerAccel v5 has software configurable settings to select between 4 sensing ranges (+/- 1.5, 2, 4, and 6g), as well as a software selectable measurement frequency (0-590Hz).

More Information & Downloads

Serial Accelerometer
Tri-Axis v5 - Enclosed

The SerAccel v5 Enclosed is a 3 axis accelerometer up to +/-6g with a simple serial interface. The latest SerAccel development, version 5 has many new improvements including variable baud rate, a factory reset command, and a complete triple axis measurement system based on the newly released MMA7260Q sensor from Freescale.

Power is gained from any RS232 port (including USB-to-RS232 converters) so no external power supply is needed. The onboard PIC (16LF88) runs at 10MHz and outputs three different types of outputs including calculated, binary, and raw outputs. The SerAccel v5 has software configurable settings to select between 4 sensing ranges (+/- 1.5, 2, 4, and 6g), as well as a software selectable measurement frequency (0-590Hz).

More Information & Downloads

Triple Axis Accelerometer Interface ADXL330

Interface board for the 3 axis ADXL330 from ANALOG DEVICES. This is the latest is a long, proven line of Accelerometers from ANALOG DEVICES - and now the holy grail has finally arrived. The ADXL330 is a triple axis accelerometer with extremely low noise and power consumption - only 320uA! Sensor ranges from +/-3g. Board comes fully assembled and tested with external components installed.

More Information & Downloads

Triple Axis Accelerometer Interface LIS302DL

This is a compact Interface board for the LIS302DL. The LIS302DL is a really impressive little IC.

Low cost, digital interface, small footprint, easy to use, and it has some great features built in.

If all you need is 8-bit resolution, this is the digital triple axis accelerometer to use.

More Information & Downloads

click to englarge

Triple Axis Accelerometer Interface LIS3LV02DQ

Interface board for the 3 axis LIS3LV02DQ accelerometer from ST Micro. Please view the datasheet for this impressive sensor! With a digital interface (SPI or I2C), the user only has to initiate commands to get 1mg resolution! Independent channels can be shut off, the sensor can be powered down, even an interrupt threshold can be set and used to awaken the sensor from power down!

Selectable ranges are available for +/-2g and 6g. This sensor is one of the first with triple axis and an easy to use digital interface. Board comes fully assembled and tested with external decoupling caps.

More Information & Downloads

click to englarge

Triple Axis Accelerometer Interface MMA7260Q

Interface board for the 3 axis MMA7260QT accelerometer from Freescale. Please view the datasheet for this impressive sensor! With a low power shut-down mode, high sensitivity output with selectable ranges (+/- 1.5, 2, 4, and 6g), this sensor is one of the very first to market with three accelerometers sensors built onto a single IC! Board comes fully assembled and tested with external filters installed.

More Information & Downloads

Triple Axis Accelerometer Interface SCA3000

This is a compact Interface board for the SCA3000 triple axis accelerometer from VTI. This highly precise and temperature compensated accelerometer is a good option for IMU and dead-reckoning applications.

The low noise and temperature compensation significantly reduces drift over time. SCA3000-D01 has an easy to use SPI interface. This Interface board includes a low noise, low drop out, 3.3V regulator that accepts voltages from 3.35V to 10V.

More Information & Downloads

WiTilt v3.0

This is the latest wireless accelerometer from SparkFun. The WiTilt v3 incorporates many new features including LiPo battery, built-in charger, enclosure, single axis gyroscope and many more! We've combined the triple axis accelerometer sensor from Freescale MMA7260Q with the Bluetooth module from Roving Networks. What do you get? The new, WiTilt v3 complete wireless Accelerometer Measurement System. All measurements are transmitted via a wireless Class 1 Bluetooth link that is extremely easy to use with a range of 100m (330ft) line-of-sight and 30m (100ft) in doors.

More Information & Downloads