Inex Single LED Driver Board

• 8mm Single LED
  
• Active with logic "1"
  
• Suitable supply voltage +3 to 5V DC
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with all Inex controller boards
  
• Includes PCB3AA-8 cable and Documentation
• Available in Red, Yellow, Blue and White colors (please select colour in shopping cart)

Inex Piezo Speaker Module

• Support signals in the frequency range of 1kHz to 3kHz
  
• Impedance: 32 ohm
  
• Supply voltage range: +3 to +6V
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with Inex controller boards

PIEZO SPEAKER MODULE DATASHEET

Dimensions: 41x23x11 mm

Inex Infrared LED Board

Use the Inex Infrared LED Board in two different modes:

Continuous Drive: In this mode, the IR-LED will receive a forward bias to drive the infrared rays. Use with the Inex Photo-transistor board for measuring the infrared light density.

Frequency Drive: This mode will modulate a 38kHz carrier frequency into the IR-LED. Use with the Inex 38kHz Infrared Receiver Module.

• A 3mm infrared LED and a current limiting resistor
  
• Drive with logic HIGH at TTL level
  
• 2-mode operation: continuous drive or frequency drive
  
• Transmission range is 5 to 10 meters (line of sight)

Dimensions: 41x23x12 mm

Inex 38kHZ Infrared Receiver Module Board

The Inex 38kHz Infrared Receiver Module is used to detect infrared signals carried by the 38kHz carrier.

If the infrared sensor does not detect the 38kHz frequency with the infrared light, the output will be logic "1". Otherwise, if it detects the 38kHz frequency, the output logic is "0".

• Detects 38KHz modulated infrared signals
  
• Active with logic "0"
  
• Data changeable at 1,200 times per second
  
• Suitable supply voltage: +5Vdc
  
• Use it with the Inex Infrared LED Board

Inex Bi-Color LED Output Board

The Inex Bi-Color LED Output Board is perfect to indicate the status of your robot. Two inputs are possible: HIGH with logic "1" will light the LED in Red; LOW with logic "0" will light the LED in Green. If the input signal is different, the LED will remain off.

• 3mm Bi-Color LED
  
• Logic "1" - LED lights Red
  
• Logic "0" - LED lights Green
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with Inex controller boards

Inex Light Sensor Board

The Inex Light Sensor Board works with an LDR (Light dependent resistor) or Photoresistor and allows you to have two different outputs: positive or negative DC voltage proportional to ambient light intensity.

• Detects ambient light density
  
• Works with a Photoresistor or LDR
  
• 2 outputs: Positive and Negative voltage reaction
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector

Inex Light Reflector Board

The Inex Light Reflector Board works with a super bright LED as a light source and an LDR (Light dependent resistor) for light detection. The red light will be reflected from any surface back to the LDR. The output voltage will increase as the LDR detects more light.

• Detects light reflection
• Includes a super-bright red LED
• Works with an LDR or Photoresisto
• Interface with microcontrollers and logic circuits
• Inex Standard 3-pin PCB connector

Vout = 2.5 + (0.0013 x Magnetic field density in Gauss units)

Inex Magnetic Field
Sensor Board

The Inex Magnetic Field Sensor works with a built-in 3A Hall-effect sensor (UGN3503) which tracks extremely small changes in the magnetic flux density. This sensor provides a voltage output from 0 to +5Vdc that is proportional to the applied magnetic field. If no magnetic field is detected (0 Gauss) the output voltage will be 2.5V.

The voltage output can be calculated using the following formula:

• Uses a 3A Hall-effect sensor (UGN3503)
  
• Provides a voltage output that is proportional to the applied magnetic field
  
• Sensitivity: 1.3mV/Gauss
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with Inex controller boards

Inex Photo-Transistor Board

Use the Inex Photo-Transistor Board in two different modes:

• Analog: The output voltage will be decreased when it detects infrared light.
  
• Digital: The output is logic "0" when the infrared light is detected.
• Detects lights with a wave length of 1mm
  
• 2-mode operation: analog or digital
  
• Can detect the candle light in Fire-Fighting Robot challenges
  
• Use it with the Inex Infrared LED board

Inex Variable Resistor Board (Horizontal)

• 300 degree turning shaft angle
  
• Output voltage varies from adjustment
  
• Supply voltage range: +3 to +6V
  
• Inex standard 3-pin PCB connector
  
• Compatible with Inex controller boards
  
• Also available with vertical shaft

Inex Variable Resistor Board (Vertical)

• 300 degree turning shaft angle
  
• Output voltage varies from adjustment
  
• Supply voltage range: +3 to +6V
  
• Inex standard 3-pin PCB connector
  
• Compatible with Inex controller boards
  
• Also available with horizontal shaft

Inex Resistance
Measurement Board

The Inex Resistance Measurement Board is designed to measure the resistance of your system, giving you an output voltage with a resolution of 1mV/ohm.

• Measures resistance up to 4000 ohm
  
• Output Resolution: 1mV/ohm
  
• Includes a 1mA constant current source
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with Inex controller boards

Inex Variable Resistor Board

The Inex Variable Resistor Board is designed to measure distance. Two output formats available: Left or Right slide direction to increase voltage.

• Use the Inex Slide Board to measure distance
  
• Supply Voltage Range: +3 to +6V
  
• Output Voltage: 0 to +5Vcc by sliding the axis
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with all Inex controller boards

Inex Switch - Touch Sensor

• High-quality push-button switch with square knob
  
• If the switch is not pressed, DATA will have a logic value of "1"
  
• Get the supply voltage from the Master/Main microcontroller board
  
• Supply voltage range: +3 to +6V
  
• On-board LED indicator
  
• Inex Standard 3-pin PCB connector included
  
• Compatible with Inex boards

Inex Temperature
Sensor Board

The Inex Temperature Sensor Board works with an NTC (Negative Temperature Coefficient) thermistor. This analog sensor allows you to have two different outputs: positive or negative DC voltage proportional to ambient temperature. Its normal resistance is set to 25C.

• Detects ambient temperature
  
• Works with an NTC thermistor
  
• 2 outputs: Positive and Negative voltage reaction
  
• Interface with microcontrollers and logic circuits
  
• Inex Standard 3-pin PCB connector
  
• Compatible with Inex controller boards

Inex Temperature
Sensor Board

The INEX ZX-Thermometer Temperature Sensor Board works with a water-resistant cabled NTC (negative temperature coefficient) thermistor (so the sensor can be placed a distance away from the board).

The output from the NTC thermistor is converted to a voltage that is directly proportional to the temperature.

MORE INFORMATION

Inex Tilt Sensor Board

• 4-Direction Tilt Sensor
  
• Sharp GP1S036HEZ Sensor with built-in super compact ball for detecting tilt direction
  
• Active with 2-bit logic
  
• 2 Status LED indicators
  
• Detects 4 directions: 0, 90, 180 and 270 degree
  
• Inex Standard 3-pin PCB connector
  
• Compatible with all Inex controller boards

MORE INFORMATION & DOWNLOADS

Inex Sound Detector Board

The Inex Sound Detector Board works with a built-in condenser microphone. This sensor provides an output voltage from 0 to +5 Vdc which is proportional to the intensity of noise detected. If the noise is louder the voltage will increase and vice versa.

• Detects ambient noise
• Built-in condenser microphone (50-15000HZ)
• Suitable supply voltage: 0 to +5Vdc
• Interface with microcontrollers and logic circuits
• Inex Standard 3-pin PCB connector
• Compatible with Inex controller boards

What's Included

• ZX-METAL board
  
• 1 JST3-8AA cable
  
• 1 Small searching coil
  
• Documentation
  

Inex Metal Detector Board with JST3AA-8 Cable

• Detect presence of any metallic object
  
• Detection Indicator
• Digital output. Active with logic “0”
  
• Operation range varies according to size of the metallic object
  
• Adjustable sensitivity
  
• An easy removable searching coil screw based terminal block
  
• JST connector for supporting all of INEX controller board
  
• Interface with any microcontroller
  
• The module has a plastic protection tray
  
• Supply voltage of +5V from the main controller board that interfaced via JST connector
  
• Available with a small searching coil. Activated via a simple proximity switch

datasheet

Inex Color Sensor Module

• Based on the TCS230 for Color Detection
  
• Outputs a variable analog voltage representing the color of an object
  
• Can also output a digital signal in color match mode
  
• Compatible with all microcontrollers
  
• Plastic base for easy & safe installation

What's Included

• ZX-Color board
  
• Small push-button switch for color matching
  
• JST3-8AA cable
  
• Documentation

Dimensions: 63x38x12mm

Inex Serial Real-time
Clock Module

The Inex Serial Real-time Clock Module is used for adding a real-time clock data for any microcontroller system. It interfaces via a serial line. Provides square wave clock signal output in 1Hz, 4.096kHz, 8.192kHz and 32.768kHz (selected by software).

• Uses the Dallas Real-time clock chip DS1307 with battery back-up
  
• Provides Hour, Minute, Second, Day, Month and Year
  
• Serial data communication
  
• Suitable for any microcontroller

MORE INFORMATION

Inex JST3AA 3-wire sensor cable (8 Inches)

• Connector cable for Inex sensors
  
• 8 inches long with two JST connectors on either end

Know somone who might be interested? Share it with them!