USBMOD1 Plug & Play
(Serial Development Module)

The USB MOD1 is a low-cost integrated module for transferring serial data over USB. Based on the FTDI FT8U232AM USB UART IC, the USB MOD1 is capable of transfer rates of up to 920k baud (RS232) and 2000k baud (RS422 / RS485).

Datasheet

USBMOD1 Serial Module Datasheet

(155 Kb)

USBMOD2 Plug & Play
(Parallel Development Module)

The USBMOD2 is a low-cost integrated module for transferring data to / from a peripheral and a host P.C at up to 8 Million bit (1 Megabyte) per second. Based on the FTDI FT8U245 USB FIFO ­ Fast Parallel Data Transfer IC, it's simple FIFO-like design makes it easy to interface to an CPU (MCU) either by mapping the device into the memory / I/O map of the PCU, using DMA or controlling the device via IO ports.

Datasheet

USBMOD2 Parallel Module Datasheet

(114 Kb)

USBMOD3 Plug & Play
(Serial Development Module)

The USBMOD3 is a second generation, low-cost integrated module for transferring serial data over USB. Based on the FTDI FT232BM USB UART IC, the USBMOD3 is capable of transfer rates of up to 1000k baud (RS232) and 3000k baud (RS422 / RS485).

Datasheet

USBMOD3 V2 Serial Module Datasheet

(324 Kb)

USBMOD4 Plug & Play
(Parallel 8-Bit FIFO)

The USBMOD4 is a second generation, low-cost integrated module for transferring data to / from a peripheral and a host PC at up to 8 Million bits (1 Megabyte) per second. Based on the FTDI FT245BM USB FIFO ­ Fast Parallel Data Transfer IC, its simple FIFO-like design makes it easy to interface to a CPU (MCU) either by mapping the device into the memory / I/O map of the CPU, using DMA or controlling the device via I/O ports.

Datasheet

USBMOD4 V2 Parallel Module Datasheet

(241 Kb)

USBMOD5 Plug & Play
USB Dual Channel UART/FIFO

The USBMOD5 is a integrated module based on the FTDI FT2232C Dual Channel USB UART / FIFO IC. The module features two Multi-purpose UART/FIFO controllers that can be configured in several different modes depending on the application.

Datasheet

USBMOD4 V2 Parallel Module Datasheet

(241 Kb)

USB I/O 24 R

The USBIO24 R is the ROHS Compliant version of our previous USB I/O 24 range. The USB I/O 24 R is a low-cost integrated module for the input and/or output of digital signals from a computer system by connection to the USB port. The modules I/O Port pin out and firmware are compatible with the previous versions of the USB I/O24 modules.

USB I/O 24 DIP Mk 1

The USB I/O 24 DIP is a Dual Inline Package version of the USB I/O 24 module. The module's 50 pin Dual Inline Package (DIP) fits into a standard 50 pin 900mil wide IC Socket. This makes the USB I/O 24 DIP ideal for rapid prototyping and development work.

Ether I/O 24
UDP/IP controlled

The Ether I/O 24 is an UDP/IP controlled digital Input/Output module. The module features three 8-bit ports with 5V level signal lines. Each of the 24 lines can be independently programmed as either an input or output. The module connects to any Ethernet network supporting the TCP/IP protocol suite and can communicate with any point on that network. By connection with an Internet Router the device can communicate with any Internet connected device.

Connector / LED Board

The I/O 24 Connector/LED Board can be connected to the I/O port of the modules to provide screw terminal connections with the optional added functionality of either pull up or pull down resistors as well as LED indication of the PORT Status.

ULN2803 Switch Board

The I/O 24 ULN2803 Switch Board shown below in diagram 1 is a very useful accessory board that allows much higher voltage and current devices to be interfaced to the low level logic provided by the I/O24 modules.