+44 (0) 1761 234 328

(0) items

£0.00

You have no items in your shopping cart.

Pololu USB-to-Serial Adapter

Product Code: 391
Excl. VAT: £10.40 Incl. VAT: £12.48
You will earn 10 Robo Points for buying this product
The Pololu USB-to-serial adapter is a tiny unit that makes it easy to connect a microcontroller project to a PC. You can connect the adapter directly to a microcontroller without an RS-232-to-TTL level converter. It is USB 2.0-compatible and will work with your existing programs that interface with a serial port.

The Pololu USB-to-serial adapter is great for connecting microcontroller projects to a personal computer. The adapter uses 3.3 V signal levels so you can connect it directly to any microcontroller running at up to 5 V without the hassle of an RS-232-to-TTL level converter. The tiny unit is less than 1.0" x 0.7" including its mini-B connector, and the simple layout of the ground, transmit, and receive lines allows for easy mounting that takes up as little as four breadboard rows.

The USB adapter’s drivers make it look like a standard serial port to the operating system, allowing you to connect to all of your existing software, such as servo controller interface programs, through a USB port. The adapter is compatible with USB 2.0 standards and allows baud rates of up to 921.6 kbps. Drivers are available for Windows 98 through Vista, Linux, and Mac OSX.

With the trend toward removing serial ports from new computers, the Pololu USB-to-serial adapter provides one of the most economical, small, and simple solutions to the common problem of interfacing small projects to PCs

Note: This product does not include printed documentation or software discs. The Pololu USB-to-serial adapter requires software drivers to operate; please see the download bar at the bottom of the page for more information.

 

Module Pinout

PIN TYPE  FUNCTION
DCD In "Data carrier detect" control input (active low)
DTR Out "Data terminal ready" control output (active low) 
(often used with DSR)
DSR In "Data set ready" control input (active low) 
(often used with DTR)
RTS Out "Ready to send" control output 
(often used with CTS)
CTS In "Clear to send" control input 
(often used with RTS)
GND Power Ground
TX Out Asynchronous serial data transmit (idle high)
VBUS Power USB bus voltage (+5V)
RX In Asynchronous serial data receive
SUSPEND  Out Driven high when in USB suspend state
SUSPEND  Out Driven low when in USB suspend state
RST In Device reset
RI In "Ring indicator" control input (active low)
VDD Power  3.3 V voltage regulator output

 

Typical connection

To connect a serial device to your computer’s USB port, you will most likely only need to use the GND, TX, and RX lines. The TX and RX lines use 3.3-volt levels, but the USB adapter input lines will tolerate up to 5.5 volts. Therefore, a direct connection to a microcontroller’s I/O lines is usually possible.

For some programs, it will be necessary to connect the handshaking lines (RTS, CTS, etc.) if the software does not establish a connection without those lines. In general, the handshaking lines can be left disconnected, used for their intended purpose, or used as additional I/O lines to the computer.

PCB size: 
1.0" x 0.65" including connector
USB standard: 
USB 2.0 (full speed)
Connector: 
USB mini-B
Data I/O voltage levels: 
3.3 V (5 V tolerant)
Maximum data rate: 

921.6 kbps
Supply current: 
25 mA

Product Attachments

View FileCP2102 USB-to-Serial Bridge Driver Installation    Size: (179.13 KB)

FeeFo Reviews

This product has no reviews yet.

Whenever possible, items which are in stock are dispatched the same day, or the next working day.

Large and/or heavy items are dispatched by UPS courier service and these orders must be placed before 15:00hrs (GMT) to ensure same day dispatch.

Small items are normally sent using a Royal Mail service for UK orders, and International Airmail or UPS for overseas orders

Returns Policy

Pololu USB-to-Serial Adapter
0