+44 (0) 1761 234 328

(0) items

£0.00

You have no items in your shopping cart.

Pololu G2 High-Power Motor Driver 24v21

Product Code: 2995
Excl. VAT: £31.99 Incl. VAT: £38.39

This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor.


The small 1.3″ × 0.8″ board supports a wide 6.5 V to 40 V voltage range and is efficient enough to deliver a continuous 21 A without a heat sink. Additional features of this second-generation (G2) driver include reverse-voltage protection along with basic current sensing and current limiting functionality.

The Pololu G2 high-power motor driver is a discrete MOSFET H-bridge designed to drive large brushed DC motors. The H-bridge is made up of one N-channel MOSFET per leg; the rest of the board contains the circuitry to take user inputs and control the MOSFETs. The absolute maximum voltage for this motor driver is 40 V, and higher voltages can permanently destroy the motor driver. Under normal operating conditions, ripple voltage on the supply line can raise the maximum voltage to more than the average or intended voltage, so a safe maximum voltage is approximately 34 V.

The versatility of this driver makes it suitable for a large range of currents and voltages: it can deliver up to 21 A of continuous current with a board size of only 1.3″ × 0.8″ and no required heat sink. The module offers a simple interface that requires as few as two I/O lines while still allowing for your choice of sign-magnitude or locked-antiphase operation. A current sense output gives an indicator of motor current, and the driver can limit the motor current to a configurable threshold. The power supply inputs feature reverse-voltage protection, while integrated detection of various fault conditions helps protect against other common causes of catastrophic failure; however, please note that the board does not include over-temperature protection.

The G2 High-Power Motor Driver 24v21 is a second-generation successor to our original High-Power Motor Driver 24v21. The G2 driver is much smaller than the original, but its interface and output capabilities make it a near drop-in replacement in typical applications. See “Differences from original high-power motor drivers” below for more details.

Features

  • Operating voltage: 6.5 V to 40 V (absolute maximum)
  • Output current: 21 A continuous
  • Inputs compatible with 1.8 V, 3.3 V, and 5 V logic
  • PWM operation up to 100 kHz
  • Current sense output proportional to motor current (approx. 20 mV/A; only active while H-bridge is driving)
  • Active current limiting (chopping) with default threshold of 50 A (can be adjusted lower)
  • Reverse-voltage protection
  • Undervoltage shutdown
  • Short circuit protection

Dimension diagram of the Pololu G2 High-Power Motor Driver 18v25 and 24v21

General specifications

Motor channels: 1
Minimum operating voltage: 6.5 V
Maximum operating voltage: 21V2
Continuous output current per channel: 25 A3
Current sense: 0.02 V/A
Maximum PWM frequency: 100 kHz
Minimum logic voltage: 1.8 V
Maximum logic voltage: 5.5 V
Reverse voltage protection?: Y

2 Absolute maximum; higher voltages can permanently destroy the motor driver. Recommended maximum is approximately 34 V, which leaves a safety margin for ripple voltage on the supply line.

3 Typical results with 100% duty cycle at room temperature.

FeeFo Reviews

This product has no reviews yet.

Whenever possible, items which are in stock are dispatched the same day, or the next working day.

Large and/or heavy items are dispatched by UPS courier service and these orders must be placed before 15:00hrs (GMT) to ensure same day dispatch.

Small items are normally sent using a Royal Mail service for UK orders, and International Airmail or UPS for overseas orders

Returns Policy

Pololu G2 High-Power Motor Driver 24v21 with included hardware
0
Post your comment

Active Robots